Why a re-roof is permitted work everywhere in Citrus County
Replacing a roof covering in Florida is permitted work. That holds in unincorporated Citrus County and inside the city limits of Inverness and Crystal River. Which office issues the permit depends on the address. The requirement does not.
The reason is the Florida Building Code. The roof is the part of the house that holds against wind, and the code sets how the deck is fastened, what underlayment goes down, how edges and flashing are detailed, and which products are approved for use in this state. The permit is how the building department checks that those things happened on your house.
Small repairs are a separate question, and what counts as small is set locally. A full replacement is not small anywhere. If someone tells you a re-roof does not need a permit, that tells you what you need to know about them.
Who pulls the permit, and why it should not be you
The contractor doing the work pulls the permit, under their own license. The license number goes on the application, and that license holder answers to the building department for the work meeting code. Ours is a Florida Certified Roofing Contractor license, CCC1333347, and you can look it up on the DBPR site.
Florida does allow an owner-builder permit. It exists for owners who do the work on their own home themselves. It does not exist so a roofer can work under the homeowner's name. When you sign an owner-builder application you take on the code responsibility for the job, and the disclosure you sign says you will not hire an unlicensed person to do it. If a roofer asks you to pull the permit, decline.
On larger jobs Florida also requires a notice of commencement, recorded with the county and posted at the site. It is there to protect you from liens. Your contractor should tell you whether your job needs one and walk you through recording it.
What the inspector looks at: dry-in versus final
A re-roof is usually inspected at least twice. The first is an in-progress inspection, usually called the dry-in, after the old roof is off and the new underlayment is down but before the covering goes on. The second is the final, after everything is installed. Some jurisdictions add a separate sheathing inspection, or accept photographs and a signed affidavit for part of it.
At dry-in the inspector is looking at what is about to be covered for good. Whether the deck is nailed to the pattern the code requires. Any decking that was replaced. The underlayment product and how it is lapped and fastened. The secondary water barrier where one is required. Drip edge at the eaves and flashing at the walls.
At the final the inspector looks at the finished roof. Whether the covering matches the product approval listed on the permit, and is fastened and exposed the way the manufacturer specifies. Flashing at walls, chimneys and skylights. Pipe boots, vents and ridge. Valleys and roof edges.
A failed inspection is not a disaster. The inspector writes up what is wrong, the contractor fixes it, and the inspection is scheduled again. What should worry you is a roof that was never inspected at all.
The dry-in is the only time anyone from the building department sees the layers that actually keep water out. After that they are covered for good.
The twenty-five percent rule: when a patch can stay a patch
The Florida Building Code limits how much of a roof can be repaired before the repair stops being a repair. The rule sits in the Existing Building volume of the code, and roofers call it the twenty-five percent rule. If more than a quarter of a roof section is repaired, replaced or recovered within a twelve-month period, the whole section has to be brought up to current code.
A roof section is not each slope. Hips, ridges and valleys do not divide one section from another. On most houses with a single roof type, the whole roof is one section. A flat porch roof tied onto a shingle roof can be its own.
There is an exception that matters on newer roofs. If the existing roof was built to the 2007 Florida Building Code or a later edition, state law allows the damaged portion to be repaired to current code without replacing the rest, even past that line. On an older roof the rule applies as written. The building official has the final word on how it applies to a given house.
So whether a patch can stay a patch depends on how much is damaged, how the roof is divided, and when it went on. It does not depend on what anyone would prefer. How your carrier treats it is between you and your carrier.
What a closed permit means later, and how to check yours
A permit is not finished when the roof is. It is finished when the final inspection passes and the building department marks the permit closed, sometimes shown as finaled. Until then it is an open permit attached to your address.
Open permits come up when you sell. Title and lien searches look for them, and a buyer's lender may want them resolved before closing. A permit that expired without a final can mean tracking down the original contractor, or getting the work inspected long after the covering went on. Some insurers ask for the permit record to confirm when the roof was replaced. What a carrier does with it is between you and your carrier. We do not perform or sign wind mitigation or four-point inspections, because a roofing license does not qualify under Florida Statute 627.711(2).
To check your own, search the address on your jurisdiction's online permit lookup, or call the building department and ask. You want the roofing permit listed with a passed final inspection and a closed or finaled status. Ask your contractor for the final inspection result too. Any contractor who did the job properly can show it to you.
The warning sign is simple. Work should not start until a permit has been issued and posted at the house. If a crew starts tearing off with no permit posted, stop the job and ask for the permit number. A contractor who starts before the permit exists is showing you how the rest of the job will go.
